Cofra Glenr Safety Boots Composite Toe Caps Composite Midsole
Model: Glenr Cofra
Description of the Cofra Glenr GORE-TEX Work Boots Waterproof Safety Boots
Black water repellent full grain leather resistant to low temperatures ankle boot, GORE-TEX membrane lining, antistatic, anti-shock, slipping resistant, non metallic APT Plate midsole Zero Perforation.
Plus: COLD BARRIER anatomic and scented footbed, insulating against low temperatures. The thermal comfort inside the footwear is granted thanks to the specials PU compound devised to give high insulation, covered with warm fabric. The leather used for these footwear is subjected to a treatment which makes them flexible and resistant to low temperatures even in the flexing areas to prevent cracks and stiffening. Sole COLD DEFENDER PU/Nitrile rubber resistant to low temperatures. Cold Defender PU is a special PU compound which guarantees higher performances than the ordinary PU for mechanical resistance to low temperatures and thermal insulation and it resist under extreme temperatures up to -25°C. The rubber outsole design has been devised to improve the slip resistance and enhance the comfort even on frozen and rambling surfaces. Padded collar.
Suggested uses: Footwear for cold temperature. Care and maintenance: Clean after each use and dry off away from direct heat; treat the leather with a suitable shoe-polish. Avoid contact with aggressive chemicals or extreme temperature. Avoid immersion in sea water, lime water or cement mixed with water.
Features of the Cofra Glenr GORE-TEX Boots
Upper made from Water repellent suede leather and BreaTEX, 3D texture, highly breathable
Lining made from GORE-TEX® Insulated Comfort Footwear
Footbed made fromCOLD BARRIER anatomic and scented footbed, insulating against low temperatures. The thermal comfort inside the footwear is granted thanks to the specials PU compound devised to give high insulation
Outer Sole made from COLD DEFENDER PU/Nitrile rubber resistant to low temperatures
Plus points MIDSOLE: Non metallic APT Plate - Zero Perforation,TOE CAP: Non metallic TOP RETURN
Width 12 Mondopoint
Safety Rating S3 WR CI HRO SRC
SIZES 6-12 39-47
This is brand new boot to the Cofra Waterproof range, the Cofra Glenr has a GORE-TEX lining, the membrane is made of 1.4 milllion pore per cm squared granting waterproofness and high breathabilit. GORE-TEX membrane protects against bacteria and resists to high temperatures.
The midsole is an APT Plate is lighter than steel being only 50 gr compared to 65gr for steel, the APT midsole also offers a better thermal insulation compared to steel midsoled boots, the APT midsole offers a better surface area protected than a steel midsole would.
It is extremely difficult to explain just how good Cofra's products is in comparison to other safety footwear.
Cofra Glenr Slip Resistance Results
|SRA : ceramic + detergent solution – flat||0.45||≥ 0.32|
|SRA : ceramic + detergent solution – heel (contact angle 7°)||0.40||≥ 0.28|
|SRB : steel + glycerol – flat||0.20||≥ 0.18|
|SRB : steel + glycerol – heel (contact angle 7°)||0.14||≥ 0.13|
"Waterproof" the test for a product to be rated as waterproof was 500 steps in 1cm of water it has now been increased to 1000 steps in 3cm of water, no material can ever be 100% waterproof it will always have some Ingres, if you are working in very wet conditions GORE-TEX lined products will give a better level of protection as they set the standard at 250,000 steps in 5cm of water, or a wellington. Wellingtons are only waterproof to a point if you are using a pressure washer this is at a much higher pressure than rain and very few wellingtons can withstand this.